ISO 9001 certified bearing manufacturer · Full size and load data on every part

Enquiry list Get a quote

Try

Search the way engineers do

  • 6205 A designation, suffix or competitor interchange reference
  • 25×52×15 Bore × outside diameter × width in mm takes you straight to bearings that fit
  • 25×52 Bore and outside diameter only, when the width is open
62 × 29 mm

Sealed deep groove ball bearings

ECB 504-20M/D

A low-profile push-in end cover for size 04 ball bearing units. 62 mm at the open end, only 29 mm deep, and fitted by hand without tools.

Outside D
62 mm
Width B
29 mm
  • Ex-stock
Request a quote
  • ISO 9001, lot traceable
  • Vibration checked per lot
  • Certificate with every shipment

Overview

ECB 504-20M/D is a push-in end cap for size 04 ball bearing units. It closes off the open side of the housing so the shaft end is no longer exposed. Nothing can snag on the turning shaft, and grit and splash water have a harder time getting at the bearing seal.

A shorter body for tight spaces

This version is 29 mm deep, a good bit shallower than our standard ECB 504. That makes it a better choice where the unit sits close to a guard, frame or another part, or where the shaft has been cut short just past the locking collar. The cover tapers from 62 mm at the open end down to 44.7 mm at the closed end, so it takes up little room around the housing.

Material and dimensions

The body is moulded in one piece from TPU (thermoplastic polyurethane). It is firm enough to keep its shape but flexes just enough to snap into the housing by hand. TPU copes well with grease, oil and the cleaning chemicals used on wash-down lines, and the cover is rated for use up to 100 °C.

  • Outside diameter at open end (D1): 62 mm
  • Outside diameter at closed end (D): 44.7 mm
  • Anchorage diameter (D2): 57.4 mm
  • Overall width (A): 29 mm
  • Weight: approx. 20 g
  • Material: TPU

Fitting and removal

  1. Clean any old grease and dirt from the housing opening.
  2. Hold the cover square to the opening.
  3. Push it in with even pressure all the way round until the rim sits flush.

When the bearing needs greasing or a check, pull the cover straight off. It can be pushed back in and used again.

Before you order

Check that the housing has a 62 mm opening and that the shaft end and locking collar fit inside the 29 mm depth of the cover. If they stick out further, the standard ECB 504 is the safer fit. Not sure which one you need? Send us the bearing unit number and we will check it for you.

Where it is used

  • Belt and roller conveyors
  • Farm and grain handling machinery
  • Food processing and packaging lines
  • Fans, blowers and air-handling units
  • Compact machines with little space beside the bearing unit

Key features

  • Short 29 mm body for tight spaces
  • Fits by hand, no tools or screws
  • TPU stands up to grease, oil and cleaners
  • Rated up to 100 °C
  • Can be removed and refitted

Typical applications

  • Conveyors
  • Farm and grain machinery
  • Food and packaging lines
  • Fans and air handling
  • Compact machines

Principal dimensions

Boundary dimensions to ISO 15. Tolerances to the precision class stated under Execution.

Principal dimensions for ECB 504-20M/D
Outside diameter (D) 62 mm
Width (B) 29 mm
Mass 0.02 kg

Load ratings and speed

Load ratings determined to ISO 281. Limiting speed assumes correct mounting, adequate lubrication and the clearance class listed.

Load ratings & speed for ECB 504-20M/D
Operating temperature range Up to +100 °C

Design and execution

Design & execution for ECB 504-20M/D
Ring & ball material Thermoplastic polyurethane (TPU)

Identification

Identification for ECB 504-20M/D
Part number ECB 504-20M/D
Manufacturer part number ECB 504-20M/D

Interchange and cross-reference

Dimensionally equivalent designations. Equivalence covers boundary dimensions; clearance, cage and sealing may differ, so check the Execution table before substituting.

Interchange designations for ECB 504-20M/D
Manufacturer Their designation Our equivalent
SKF ECB 504-20M/D ECB 504-20M/D

Third-party designations and trademarks are the property of their respective owners and are quoted for identification only. China Bearing Manufacturer is not affiliated with, nor endorsed by, those manufacturers.

Questions engineers ask about this bearing

What does the ECB 504-20M/D fit?

It is an end cover for size 04 ball bearing units with a 62 mm housing opening.

How is it different from the standard ECB 504?

It is shallower, at 29 mm overall, so it suits units with little space in front of the housing or a short shaft end.

Do I need tools to fit it?

No. Line it up with the housing opening and press it in by hand until the rim sits flush.

What temperature can it handle?

The TPU body is rated for use up to 100 °C.

Can the cover be reused after removal?

Yes. Pull it straight out for greasing or inspection, then press it back in.

Need a price for ECB 504-20M/D?

Tell us the quantity and the application. Price, lead time and an engineer’s recommendation, usually within one working day.

Request a quotation
ECB 504-20M/D Price on application
Get a quote

Quote for ECB 504-20M/D

Quantity and application are enough to start. We will come back with price, lead time and any better-suited designation.

Speed, load, temperature, mounting arrangement and the designation you are replacing all help us answer in one pass.

We use your details only to answer this enquiry. See our privacy policy.