ECB 505
A full-depth end cover for size 05 ball bearing units. 71.5 mm at the open end, 34.5 mm deep, moulded in one piece from TPU.
- Outside D
- 71.5 mm
- Width B
- 34.5 mm
- Ex-stock
- ISO 9001, lot traceable
- Vibration checked per lot
- Certificate with every shipment
Overview
ECB 505 is a full-depth end cover for size 05 ball bearing units. It pushes into the open side of the housing and encloses the shaft end, so there is no exposed rotating part for clothing or tools to catch on. Less dirt and moisture reach the bearing as well.
Room for the shaft end and collar
With 34.5 mm of depth, this cover leaves space for a shaft that runs a little past the locking collar or eccentric ring. It is the one to start with for most size 05 units. Where the space in front of the housing is tight, the shorter ECB 505/D at 29 mm is the alternative.
Material and dimensions
The cover is made in a single shot of TPU. It is tough, slightly flexible and keeps a snug fit in the housing even after it has been taken out and refitted a few times. It handles grease, oil and the usual plant cleaners, and it runs at temperatures up to 100 °C.
- Outside diameter at open end (D1): 71.5 mm
- Outside diameter at closed end (D): 53.7 mm
- Anchorage diameter (D2): 67.1 mm
- Overall width (A): 34.5 mm
- Weight: approx. 20 g
- Material: TPU
Fitting and removal
- Remove dirt and old grease from the housing opening.
- Line the cover up straight with the bore.
- Push firmly and evenly around the edge until it sits flush.
Need to service the bearing? Pull the cover out straight, do the work, then push it back in.
Before you order
The housing opening should measure 71.5 mm. Also check that whatever stands out of the housing, such as the shaft end, set screws or collar, fits within 34.5 mm. Send us the unit number if you would like us to check it for you.
Where it is used
- Bulk material conveyors and bucket elevators
- Farm and grain machinery
- Food and drink processing lines
- Industrial fans
- Woodworking and textile machines
Key features
- Full 34.5 mm depth covers longer shaft ends
- Fits by hand, no tools or screws
- TPU holds up to grease, oil and cleaners
- Rated up to 100 °C
- Reusable after removal
Typical applications
- Bulk material conveyors and bucket elevators
- Farm and grain machinery
- Food and drink processing lines
- Industrial fans
- Woodworking and textile machines
Principal dimensions
Boundary dimensions to ISO 15. Tolerances to the precision class stated under Execution.
| Outside diameter (D) | 71.5 mm |
|---|---|
| Width (B) | 34.5 mm |
| Mass | 0.02 kg |
Load ratings and speed
Load ratings determined to ISO 281. Limiting speed assumes correct mounting, adequate lubrication and the clearance class listed.
| Operating temperature range | Up to +100 °C |
|---|
Design and execution
| Ring & ball material | Thermoplastic polyurethane (TPU) |
|---|
Identification
| Part number | ECB 505 |
|---|---|
| Manufacturer part number | ECB 505 |
Interchange and cross-reference
Dimensionally equivalent designations. Equivalence covers boundary dimensions; clearance, cage and sealing may differ, so check the Execution table before substituting.
| Manufacturer | Their designation | Our equivalent |
|---|---|---|
| SKF | ECB 505 |
ECB 505 |
Third-party designations and trademarks are the property of their respective owners and are quoted for identification only. China Bearing Manufacturer is not affiliated with, nor endorsed by, those manufacturers.
Questions engineers ask about this bearing
What size housing does the ECB 505 fit?
It fits size 05 ball bearing units with a 71.5 mm housing opening.
When should I choose the ECB 505 over the ECB 505/D?
Choose the ECB 505 when the shaft end or collar sticks out further than 29 mm. Its 34.5 mm depth gives that extra room.
How is it installed?
Clean the opening, hold the cover square and press it in by hand until the rim is flush.
What temperatures can it take?
The TPU body is rated for use up to 100 °C.
Does it need replacing after removal?
No. If the rim is undamaged, it can be pressed back in and used again.
Need a price for ECB 505?
Tell us the quantity and the application. Price, lead time and an engineer’s recommendation, usually within one working day.
