ECB 506-30M/D
A low-profile end cover for size 06 ball bearing units. 81.2 mm across the open end, 31 mm deep, and fitted by hand.
- Outside D
- 81.2 mm
- Width B
- 31 mm
- Ex-stock
- ISO 9001, lot traceable
- Vibration checked per lot
- Certificate with every shipment
Overview
ECB 506-30M/D is a shallow end cover for size 06 ball bearing units. Pressed into the open side of the housing, it puts a solid cap over the shaft end. Nothing can wrap around the turning shaft, and the bearing seal is better shielded from dust and splash.
Less depth for crowded mountings
This cover is 31 mm deep, 5 mm shorter than the standard ECB 506. That is often just enough to clear a guard, chain case or frame rail mounted close to the bearing unit. It keeps the full 81.2 mm rim of the size 06 cover and narrows to 63.8 mm at the closed end.
Material and dimensions
The cover is one solid TPU moulding. It flexes enough to click into the housing by hand and then stays put. Grease, oil and ordinary wash-down products do not attack it, and it can be used at up to 100 °C.
- Outside diameter at open end (D1): 81.2 mm
- Outside diameter at closed end (D): 63.8 mm
- Anchorage diameter (D2): 76.7 mm
- Overall width (A): 31 mm
- Weight: approx. 30 g
- Material: TPU
Fitting and removal
- Clean out the housing opening so no old grease or grit is left.
- Hold the cover level with the bore.
- Push in with both thumbs, working round the rim, until it is seated.
To reach the bearing, pull the cover straight out. It can be pressed back in afterwards if the rim is still in good shape.
Before you order
Your housing opening should be 81.2 mm, and the shaft end plus collar must fit inside 31 mm. If they stand out further, the standard ECB 506 gives you 36 mm. Send us the bearing unit designation and we will confirm which one fits.
Where it is used
- Chain and belt conveyors
- Grain and seed handling machines
- Packaging and palletising lines
- Fans and blowers
- Size 06 units mounted close to guards or frames
Key features
- 31 mm overall width, shorter than the standard size 06 cover
- Presses in by hand, no fasteners
- TPU resists grease, oil and cleaners
- Rated up to 100 °C
- Can be removed and refitted
Typical applications
- Chain and belt conveyors
- Grain and seed handling machines
- Packaging and palletising lines
- Fans and blowers
- Size 06 units mounted close to guards or frames
Principal dimensions
Boundary dimensions to ISO 15. Tolerances to the precision class stated under Execution.
| Outside diameter (D) | 81.2 mm |
|---|---|
| Width (B) | 31 mm |
| Mass | 0.03 kg |
Load ratings and speed
Load ratings determined to ISO 281. Limiting speed assumes correct mounting, adequate lubrication and the clearance class listed.
| Operating temperature range | Up to +100 °C |
|---|
Design and execution
| Ring & ball material | Thermoplastic polyurethane (TPU) |
|---|
Identification
| Part number | ECB 506-30M/D |
|---|---|
| Manufacturer part number | ECB 506-30M/D |
Interchange and cross-reference
Dimensionally equivalent designations. Equivalence covers boundary dimensions; clearance, cage and sealing may differ, so check the Execution table before substituting.
| Manufacturer | Their designation | Our equivalent |
|---|---|---|
| SKF | ECB 506-30M/D |
ECB 506-30M/D |
Third-party designations and trademarks are the property of their respective owners and are quoted for identification only. China Bearing Manufacturer is not affiliated with, nor endorsed by, those manufacturers.
Questions engineers ask about this bearing
Which bearing units does the ECB 506-30M/D fit?
Size 06 ball bearing units with an 81.2 mm housing opening.
How does it compare with the ECB 506?
It is 31 mm deep instead of 36 mm, so it suits installations with less room in front of the housing.
Do I need tools to fit it?
No. It presses into the housing by hand.
What temperature is it good for?
The TPU body is rated for use up to 100 °C.
Can it be refitted after removal?
Yes, as long as the rim is not damaged.
Need a price for ECB 506-30M/D?
Tell us the quantity and the application. Price, lead time and an engineer’s recommendation, usually within one working day.
