F2B 010-TF
Oval 2-bolt flanged ball bearing unit for 5/8 in shafts, with an extended inner ring, set screw locking and flinger seals.
- Bore d
- 15.875 mm
- Width B
- 32.9 mm
- Dynamic C
- 9.56 kN
- Static C₀
- 4.75 kN
- Limiting speed
- 9,500 r/min
- Ex-stock
- ISO 9001, lot traceable
- Vibration checked per lot
- Certificate with every shipment
Overview
F2B 010-TF is an oval two-bolt flange unit for 5/8 in (15.875 mm) shafts. The cast iron housing holds a sealed insert bearing with an extended inner ring and set screw locking. It is made to North American inch standards and is a solid everyday choice for conveyors and handling equipment.
Extended inner ring with flinger seals
The YAR 203-010-2F insert has a 27.4 mm wide inner ring that sits on the shaft with two set screws. This works for shafts that turn one way or switch direction. A flinger on each side throws off coarse dirt before it reaches the contact seal behind it.
Specifications
- Shaft diameter (d): 5/8 in (15.875 mm)
- Bolt hole centres (J): 76.2 mm
- Overall height (H): 98.4 mm
- Overall length (L): 60.3 mm
- Housing width (A): 24 mm
- Overall width (T): 32.9 mm
- Inner ring width (B1): 27.4 mm
- Bolt holes (N): 11.11 mm, for 3/8 in or M10 bolts
- Basic dynamic load rating (C): 9.56 kN
- Basic static load rating (C0): 4.75 kN
- Fatigue load limit (Pu): 0.2 kN
- Limiting speed: 9 500 r/min (h6 shaft)
- Insert bearing: YAR 203-010-2F (extended inner ring, set screw locking)
- Locking: Two #10-32 UNF set screws, tightened to about 4 N·m
- Sealing: Contact seal and flinger on both sides
- Housing: cast iron, oval 2-bolt flange, with grease fitting
- Weight: approx. 0.366 kg
Mounting tips
- Wipe the shaft clean and remove any burrs.
- Slide the unit into position and bolt it to the frame.
- With the shaft aligned, tighten both set screws to about 4 N·m.
- Use the grease fitting to relubricate at regular intervals.
Typical applications
- Conveyors in dusty conditions
- Material handling equipment
- Farm machinery
- Reversing drives
Key features
- Fits 5/8 in (15.875 mm) shafts
- Extended inner ring for extra shaft support
- Two set screws
- Seals with flingers on both sides
- Cast iron 2-bolt oval flange
Typical applications
- Conveyors in dusty conditions
- Material handling equipment
- Farm machinery
- Reversing drives
Principal dimensions
Boundary dimensions to ISO 15. Tolerances to the precision class stated under Execution.
| Bore diameter (d) | 15.875 mm |
|---|---|
| Width (B) | 32.9 mm |
| Mass | 0.366 kg |
Load ratings and speed
Load ratings determined to ISO 281. Limiting speed assumes correct mounting, adequate lubrication and the clearance class listed.
| Basic dynamic load rating (C) | 9.56 kN |
|---|---|
| Basic static load rating (C₀) | 4.75 kN |
| Fatigue load limit (Pu) | 0.2 kN |
| Limiting speed | 9500 r/min |
Design and execution
| Sealing | Two contact seals (2RS) |
|---|---|
| Factory lubricant | Grease, relubricatable |
| Ring & ball material | Bearing steel insert, cast iron housing |
Identification
| Part number | F2B 010-TF |
|---|---|
| Manufacturer part number | F2B 010-TF |
| Conforms to standard | North American (inch) |
Interchange and cross-reference
Dimensionally equivalent designations. Equivalence covers boundary dimensions; clearance, cage and sealing may differ, so check the Execution table before substituting.
| Manufacturer | Their designation | Our equivalent |
|---|---|---|
| SKF | F2B 010-TF |
F2B 010-TF |
Third-party designations and trademarks are the property of their respective owners and are quoted for identification only. China Bearing Manufacturer is not affiliated with, nor endorsed by, those manufacturers.
Questions engineers ask about this bearing
What shaft size is F2B 010-TF for?
5/8 in (15.875 mm).
What does the extended inner ring do?
It gives the set screws a wider seat on the shaft, and the ring is 27.4 mm wide in total.
Can it run in both directions?
Yes. Set screw locking works for constant or alternating rotation.
What protects the bearing?
A contact seal and a flinger on each side.
Need a price for F2B 010-TF?
Tell us the quantity and the application. Price, lead time and an engineer’s recommendation, usually within one working day.
