F2B 012-TF-AH
Air handling version of the 3/4 in oval flange unit, with set screw locking, flinger seals and a cast iron housing.
- Bore d
- 19.05 mm
- Width B
- 37.4 mm
- Dynamic C
- 12.7 kN
- Static C₀
- 6.55 kN
- Limiting speed
- 8,500 r/min
- Ex-stock
- ISO 9001, lot traceable
- Vibration checked per lot
- Certificate with every shipment
Overview
F2B 012-TF-AH is the air handling member of our 3/4 in (19.05 mm) flange unit range. A cast iron two-bolt housing holds a sealed insert bearing with set screw locking, ready to mount on a fan frame or air handling unit. It follows North American inch standards.
Specified for fans and blowers
This unit is intended for air handling duty, where shafts often run steadily for long hours. Its size and load ratings match the F2B 012-TF, so both fit the same 89.7 mm bolt pattern.
Inside the unit
The YAR 204-012-2F insert has an extended inner ring held by set screws. A flinger and a contact seal on each side keep dust carried in the airflow away from the raceways.
Specifications
- Shaft diameter (d): 3/4 in (19.05 mm)
- Bolt hole centres (J): 89.7 mm
- Overall height (H): 113 mm
- Overall length (L): 60.3 mm
- Housing width (A): 29 mm
- Overall width (T): 37.4 mm
- Inner ring width (B1): 31 mm
- Bolt holes (N): 11.11 mm, for 3/8 in or M10 bolts
- Basic dynamic load rating (C): 12.7 kN
- Basic static load rating (C0): 6.55 kN
- Fatigue load limit (Pu): 0.28 kN
- Limiting speed: 8 500 r/min (h6 shaft)
- Insert bearing: YAR 204-012-2F (extended inner ring, set screw locking)
- Locking: Set screws (1/4-28 UNF), about 4 N·m
- Sealing: Contact seal and flinger on both sides
- Housing: cast iron, oval 2-bolt flange, with grease fitting
- Weight: approx. 0.428 kg
Mounting tips
- Check that the fan shaft is clean and free of burrs.
- Bolt the flange to the fan frame with 3/8 in or M10 bolts.
- Align the shaft and tighten the set screws to about 4 N·m.
- Relubricate on the service schedule set by your fan maker.
Typical applications
- Centrifugal fans
- Air handling units
- Blowers and exhaust fans
- HVAC systems
Key features
- Specified for air handling
- Fits 3/4 in (19.05 mm) shafts
- Set screw locking
- Seals with flingers
- Up to 8 500 r/min
Typical applications
- Centrifugal fans
- Air handling units
- Blowers and exhaust fans
- HVAC systems
Principal dimensions
Boundary dimensions to ISO 15. Tolerances to the precision class stated under Execution.
| Bore diameter (d) | 19.05 mm |
|---|---|
| Width (B) | 37.4 mm |
| Mass | 0.428 kg |
Load ratings and speed
Load ratings determined to ISO 281. Limiting speed assumes correct mounting, adequate lubrication and the clearance class listed.
| Basic dynamic load rating (C) | 12.7 kN |
|---|---|
| Basic static load rating (C₀) | 6.55 kN |
| Fatigue load limit (Pu) | 0.28 kN |
| Limiting speed | 8500 r/min |
Design and execution
| Sealing | Two contact seals (2RS) |
|---|---|
| Factory lubricant | Grease, relubricatable |
| Ring & ball material | Bearing steel insert, cast iron housing |
Identification
| Part number | F2B 012-TF-AH |
|---|---|
| Manufacturer part number | F2B 012-TF-AH |
| Conforms to standard | North American (inch) |
Interchange and cross-reference
Dimensionally equivalent designations. Equivalence covers boundary dimensions; clearance, cage and sealing may differ, so check the Execution table before substituting.
| Manufacturer | Their designation | Our equivalent |
|---|---|---|
| SKF | F2B 012-TF-AH |
F2B 012-TF-AH |
Third-party designations and trademarks are the property of their respective owners and are quoted for identification only. China Bearing Manufacturer is not affiliated with, nor endorsed by, those manufacturers.
Questions engineers ask about this bearing
What is F2B 012-TF-AH used for?
It is specified for air handling equipment such as fans and blowers.
Is it the same size as F2B 012-TF?
Yes. Dimensions and load ratings are the same.
What shaft does it fit?
A 3/4 in (19.05 mm) shaft.
What is the limiting speed?
8 500 r/min with an h6 shaft.
Need a price for F2B 012-TF-AH?
Tell us the quantity and the application. Price, lead time and an engineer’s recommendation, usually within one working day.
